Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
i am working on nRF52832.
i was successfully build a code for scanning without using FreeRTOS
Now i want to use FreeRTOS with my scanning code
But i am not...
Hi ,
i am using ble ancs profile in my project, i was getting internal error (error no 3) while connecting.
the error is being reported by two of the following event handlers...
I have managed to establish a proper TLS connection with the proper credentials, but it seems that TLS session resumption is missing from my implementation since my device...
Hello:
I am now working with nrf5_SDK_for_Mesh_v3.0.0 and I try to implement OTA for mesh dfu. However, I found that the v4.0.0 has a dfu_no_serial_nrf52832_xxAA_s132_7_0_1...
Hello,
I've just recently started learning to develop on the nrf52 platform after 2 years of frustration trying to learn of how to develop on the Nordic platform I finally...
I am trying to set the Lifecycle state of the cryptocell, but it seems like I am having an issue.
I do
/** Enable crypto cell to configure it **/ NRF_CRYPTOCELL->ENABLE...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
hi.
I wonder if nRF52840 dongle has an unchangeable bootloader, and if so, where we can download it. PCB of nRF52 dongle is available on the official website, but not in...
Hi there,
in my passion to keep up with technological advances, I ordered the nRF5340 PDK. I was hoping to pave the way of moving our nRF52832 and nRF52840 based projects...
