Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi,
I'm using an nRF52832 with SDK 14.2 and FreeRTOS. I'm hitting a configASSERT when I call nrf_fstorage_erase. I called the function after calling ble_stack_init but before...
Hi,
I'm using interactive PyACI on Windows i found an error as in image attached. I didn't understand what can i do with Interactive PyACI and what it will deliver to me...
Hi,
SDK 16 using board NRF58240dk. PCA 10056. Segger studio on windows.
I am trying to read a current pulse train from a peripheral device. This device outputs a 4mA pulse...
I am working with the Nordic NRF52840. I need a way of reading current pulse counts over a two wire system coming in from an external sensor. This external sensor is reliable...
Hi,
I am using 2 development kits 52840-DK.
I run the examples projects transmitter ( pca1056 ) and receiver. It works,
In an attempt to get longer range I increased...
Hi Nordic,
I had built a BLE custom service which has two characteristics and now I'm merging this with light-switch example, but while building it i got a problem which...
Dear All,
I'm pretty sure this has been asked many times but I don't know the right keywords to search for.
Alright, on our custom board we have a PMIC with regulated...
I try to start working with the nRF9160-DK. I gone trough all steps of the Getting Started Assistent from nRF Connect SDK. But i have a Problem with setting up a Project in...
Hi,
In my NRF52840 based application, I have a situation where the peripheral needs to pass 2K to central.
In order to speed up the xfer, I'm requesting a Connection Parameter...
Hi,
I am using nrf52832 and I want to build a device that can advertise iBeacon signals and can transmit data to another BLE device (central) simultaneously.
Can I do...
Hi,
I use example nRF5SDKforThreadandZigbeev3209fade31\examples\dfu\secure_bootloader\pca10056_uart to upgrade bootloader and coordinator application.
I try to upgarde...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
