Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
I'm debugging on an nRF52832 (nRF52-DK, non-preview) using the ARM GCC toolchain and GDB under Eclipse on Ubuntu 14.04LTS, set up following the devzone tutorial .
At various...
When calling sd_ble_gap_connect(), and providing a whitelist, what is the expected process for establishing a connection, as far as timing is concerned? Will the device scan...
nRF52840. In case of standby current (battery only)
Measured as follows:
With only the battery connected, the same current draw as the one attached. Is there any...
In my DFU bootloader I am protecting areas of Flash memory used to store user data.
After an update, when my application starts and tries to write to this memory it is causing...
I am trying to use the real time clock on the nRF52840 dongle using the pc-ble-driver. However, my nrf.h file has nothing in it but the following:
#ifndef NRF_H__ #define...
I have a working iBeacon advertising a beacon UUID, Major, & Minor on a nRF52832. In addition, I also have a single BLE service (which has a single characteristic) defined...
Hi I am managing to initialize a serial instance using uart0 within the BLE Buttonless DFU Template. However when I carry out a similar process for uart1 I get the following...
Team,
I received the following customer inquiry and hope you can help:
The BLE – WiFi bridge project I’m working on will need to control up to 64 nodes, not concurrently...
Hello,
I am trying to upload the firmware with secure DFU using following method:
generated the dfu_public_key.c and private.pem pair
copied the " dfu_public_key.c...
Hi Dear Team,
I am using the nRF52840-Dongle and pc-ble-driver-py-0.12.0 for the ble development, while I encounter a problem about the max connection per device.
I use...
Hi,
I've got some questions about setting up a connection.
I want to connect as fast as possible with a UUID filter. Is it possible to connect directly on the first advertising...
How to set 250kbps PHY Coded in NRF52832 BLE Mesh? I have tried to change scanner_config_radio_mode_set(RADIO_MODE_BLE_1MBIT); to scanner_config_radio_mode_set(RADIO_MODE_NRF_250KBIT...
Hai ,
I need to update nrf52840 over ble from esp32 . first i tried with app , firmware gets updated .. as per the dfu protocol i understood flow and tried to writing data...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
