We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am developing a custom board using nRF52810.
SoftDevice S112 6.0.0 and SDK 15.0.0 are in use.
I want to know the maximum current in Idle state .
Current measurements...
Hi all,
I am currently trying turning off the active time, so that the nrf9160 immediately goes in power save mode after RRC Connected Release.
If I send the command ...
I connect VBUS to VDDH, and use a USB cable for power supply(high voltage mode), but I cannot download firmware into the 52840.
Unless I power the 52840 from the VDD pin...
Hello,
I'm a teacher. I use the microbit card that loads one of your components. Nordic nRF51822-QFAA-R rev 3 Could you tell me if this processor is based on a Von Neumann...
Hello, just a few quick short questions regarding nrf52 devices:
Do I have to configure and initialize them before using?
Which function should I use? I...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Issue-background...
Hello,
nRF52840-DK
SDK 15.3.0
SoftDevice: s140
IDE: SES
Example: Flash_fstorage_s140_pca10056
I do not read back the expected value in the example. The terminal...
Hi, I am trying to do DFU OTA. I am using SDK v16.0, s140_nrf52_7.0.1_softdevice.hex, SES and nRF52840 dev kit. I am finished with my application and it functions as expected...
Hi,
We are a module manufacturer. We are making modules based on WLCSP, QFN based nRF52840 SoC.
Can you please provide software(preferably GUI) available for module FCC...
Hi guys, i can't figure out how to create an event handler in my Mesh Client.
The functionality of this handler should be to set a flag on the 'NRF_MESH_EVT_TX_COMPLETE...
I used keil v4 compile the following project F:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\pca10040\s112\arm4\_build get file nrf52832_xxaa.hex of size 101kb...
Hello ...
I'm porting our product from RF Digital's Simblee to Laird's BL651 (nRF52810). A phototransistor measures light, is connected to an analog pin, and is sampled...
Hello guys! And girls
My project is working as expected in SDK14.2. I'm updating adv data (manuf. spec. data) without any problem with this function But in SDK15 the function...
Hello,
I'm working on a project using a Thread network to send MQTT packets and I'm having an issue with the example project out of the box. I'm running the version 3.2...
