Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello, Guys. Using the function ble_nus_string_send, I've sent sensor values to my mobile phone. However, the data received came from an unknown character being broken. I...
Hello,
I use aws_fota as starting point on a mobile device with MQTT reporting.
What is the best way to manage loss of connection (how to know and how to cleanly rebuild...
Hello Nordic support
We want to add a function to monitor the RSSI of the other party's mobile phone at the time of Connetion instead of advertising. Is it possible...
Hello Nordic Support,
I have modified the USB MSC example to use SD card and have also initialized UART port. Basically, what I'm trying to achieve is to write data received...
Hi,
Question 1: Why nRF52832 not supporting Thread? Is it because Memory? Hardware?
Question 2: Can you advise what is the advantages or applications to use BLE+Thread...
Hi,
I'm sorry but i cannot find in the discussion the definition of this structure NRF_SPIM_Type
it is not defined in nrf_spim.h
typedef struct { NRF_SPIM_Type * p_reg;...
Hi,
We are looking for an industrial solution to program our NRF52832 on a custom board, until now we are using the programming chip directly from the NRF52DK, it works...
My custom board with NRF52810 is done and I'm now trying to get some examples working. I am adapting blinky_s132 in SES. To do this I edited the project options including...
i'm new to this board can you find some course for this board
from scratch the courses will be very helpful
just the video tutorials are very advanced
the documentations...
Hi folks,
I am working on ble_app_uart example program nRF52 SDK 15.2 Verion , in this case i am writing the data in flash for future use , Now i am to get the specific...
Hi Team,
We are using nRF52840 DK with sensors. We developed a custom code that is working fine. But the issue is current consumption. Showing below the readings.
The...
I have taken the code found here:
https://github.com/bjornspockeli/custom_ble_service_example
and modified it so that the custom characteristic is located in user memory...
Hi,
Good day!
I tried to add the RTC2 driver to our application and i keep getting this compiler error message (using sdk16.0).
Here is my sdk_config.h. Not sure why...
Hi
I'm planning to connect three different BLE peripheral like Heart-rate sensors, Health Thermometer, and Blood Pressure to a Central BLE device.
I'm using a small customized...
Hello
What is the specified max current on the supply pins for nRF52840?
The GPIO pins are specified to source max 14mA in 'high drive' mode:
How many of these pins...
