Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
I use spi_slave with SDK 9.0.0. SPI slave is working, but there is some current leak when it become system off mode. I think the reason is that MISO is HI-Z at that time....
Hello,
I have a nrf51822 chip that I would like to flash using Segger Flasher in Stand-alone mode. When I am trying to load the program to the chip I get the following...
I'm trying to add DFU service support to my application on an nRF51 development board, using the instructions here: Adding DFU Service support to an application . I'm using...
I am not a native English speaker, I am totally confused with this line of code where I have found in many samples
#define APP_ADV_INTERVAL 300 /**< The advertising interval...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hi,
I have an issue in using GPIOTE_IRQHandler.
Let me give an explanation about our implementaiton.
we have nRF controller which is connected to STM32 controller...
Hi
Is possible to use GAP White-list to restrict connections without the bond manager system ?
Just by save the white-list with pstorage.....
for exemple, first open...
Hi,
I'm using S110 on PCA10028, I have problems with byte receiving on UART and can't make it work.
I can easily send and receive data over terminal using UART. I can...
Hello,
i use notifications with sd_ble_gatts_hvx. If I push a lot of data, are notifications overwritten or do they are fifoed ?
How to do a kind of flow control to...
So I'm just getting started with NRF51822 and BLE in general; I have built a simple prototype with the BLE Nano using Arduino+BLEPeripheral library. I have converted that...
Hello,
I've read that some devices (e.g. Nexus 4 and Nexus 7) notify only about the first adv. packets from connectible peripheral and the only solution is to disable continuous...
Hello
I am working on a proprietary radio protocol while dealing with a problem that I stuck at for 2 days now. I am managing to get the radio stuck in a TX state (NRF_RADIO...
Hi,
I would like to ask a question about the power consumption specified in nRF8001 datasheet:
the graph on page 40 shows that the average current consumption is about ...
uart not accepting my static passkey when i added dfu in my project. using ios app nrftoolbox.
programed soft device s110. programed dfu dual bank example project then uploaded...
