here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I would like to know can i configure advertising interval for more than 10.24 seconds.
Which are the functions i can use for configuring advertising interval.
Also...
Hi All,
Yesterday while (unsuccessfully) trying to get my dongle to work with Antware II, I did something I'm not sure what it was, but has caused the following:
MCP ...
I'm developing application on nrf51 for that i'm using...
SDK : nRF51_SDK_8.1.0_b6ed55f
Board : PCA10028
I'm trying to run code from SDK examples C:\nRF51_SDK_8.1.0_b6ed55f...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
every time I try to add a new example in Keil microvision, it dont work me.
last time I try to import a new pack, I got this error:
pack instalation failled...
I use SD 7.1.0. My own app works perfectly. I use my own PCB, debugger J-Link Segger.
I try to upload any app via bootloader from SDK's example (modified in LED_pins dfu_dual_bank_ble_s110_pca10028...
I'm trying to send over a ble the data for a tablet
I'm trying to use the example of analogues (NordicSemiconductor/nrf51-ADC-examples) an old time I get error response...
Hi,
While calculating the power consumption according S110 soft device specification only ION current has been considered.
So does ION include current consumed by DCDC...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
i work with the nrf51 example for ble and sd130 (nrf51 dongle and sniffer) and now i like to use sd310 for ble and ant+. is there also a example for sd310 (or sd110)?
Th...
Hello everyone,
I am using ADC functionality with NRF51822 and its working fine, Interrupt is raising when ever i give input to Analog Pin. Communication protocol i use is...
Hello.
I'm trying to start developing with the nRF51822 Eval kit with Eclipse and ARM GCC but I ran into some problems when trying to run the ble_app_hrs_example. I've been...
I have enabled a gpiote module, it does not set gpiote_enabled to 1.
I have tried deleting the file in the RTE folder with no success. I have tried disabling and enabling...
