Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I'm using a nRF51 beacon as a receiver that produces a pulse when it receives a byte from the transmitter. The code is based on the ble_app_uart example. And I set the connection...
The new v3 of sd132 now has 4 characteristics in the GAP service.
The new one has uuid 2AA6
For some legacy testing I need to disable it's inclusion.
I have searched the...
Hi
I'm using the connectivity interface of the softdevices a lot and recently failures in the documentation of the connectivity protocol caused a long debug session. Maybe...
Hello,
I want to use the NUS service on my BLE communication. I don't have pins connected for UART, do I need to have them?
When I try to run the device, my program initializes...
hi,
1/ i notice that drivers header files are available in two versions. one inside "components\drivers_nrf" folder and the other inside "components\libraries".
and...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I modified the app_ble_hrs example to send 2x 20B packets of data (via a modified heart_rate_meas_send() function) upon a m_battery_timer_id...
Hi
I have a custom board with no external crystal. Using S130 works fine, but I want to enhance communication with some data being sent over ESB using timeslot API.
...
My English is still poor, but I hope you can understand me.
Press the button to call ble_advertising_start(), which may occasionally restart main.
I set a short timeout...
I am using the FreeRTOS port included in a nRF52832 with nRF5 v11.0.0 + s132. From main() I create a task and I pass it some input data as argument. That data is encapsulated...
Hi,
I am struggling with I2S. While I was debugging my I2S data handler function, I found something interesting. I copy one element from a uint32 buffer into a (static...
Hello all!
Simple question: What is a SNR value for BT LE? I read 20 dB are OK, but I would like some sources/informations to back this number up.
Thanks!
Cheers...
I am using a custom nrf51822 board and S130.
I am trying to pull data from a sensor over SPI and then immediately send that data over SPIS to another processor. Is this...
While trying to implement a simple qdec demo application, I find that QDEC_SAMPLEPER_SAMPLEPER_512us above works ok, yet QDEC_SAMPLEPER_SAMPLEPER_256us does not work at all...
I have a case where I'm using a timer/counter as a counter with one PPI channel routing a GPIO rising edge to the COUNT task. Another GPIO rising event controls the counting...
