Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I am using mesh SDK 4.0.0 and nRF SDK 16.0.0. I ported the ble_app_uart_coexist example from mesh SDK to build OK for pca10056 board (nRF52840) by following the instructions...
I'm attempting to receive SMS in eDRX mode. It succeeds when nRF9160 device is left in a place without moving it.
However, when I move it to a far place like a few kilometers...
Hey..
I'm using the nRF52840-preview evk, with the Arduino camera plugged into the side connector. PCA10056_USE_FRONT_HEADER is set to 0, and I'm using the SES project....
Hello, guys!
I recently started playing with nRF9160 SiP module. nRF Connect SDK is properly installed and I am able to build the code and download it properly. I also spent...
I have a nRF52832 Breakout Board, in which i programmed using arm cortex debug connector, using Segger Emmbedde Studio. I uploaded one example from nRF5_SDK_15.3.0, the propramm...
Hello;
we are having a communication issue(a BIG one at this point) that we are experiencing with our BLE 4.0 tablets. Our device(has NRF52832) is designed to communicate...
I noticed some weird behaviour which I can repeat to do with not being able to register after reading back the ICCID.
The following after the list of commands I run on bootup...
Hi,
I'm trying to update the FW of my nRF9160-DK.
Running MacOs Mojave 19.14.6. Installed nRF Connect 3.3.0. This is the log after startup of nrf connect:
2020-01-24T15...
Hi
I've checked the two PWM examples in SDK, pwm_driver and pwm_library, they seem too complex for me to understand, does anyone know where I can find a simple PWM example...
Your download page for nRF-Command-Line-Tools is not working and it redirects to "page not found (Error 404)". I am using this link https://www.nordicsemi.com/Software-and...
I am currently working on a project where I am checking an input > 3V then passing it to ADC and increasing count based on it. The count value increases or stays the same...
I'm going to write to inquire about Bluetooth Low Energy Device Beacon which will be smallest in size and can operate with coin cell battery and also able to communicate two...
Trying to build the app from C:\Users\xxxx\Documents\SEGGER Embedded Studio for ARM Projects\nRF5SDK160098a08e2\examples\ble_central_and_peripheral\experimental\ble_app_interactive...
Hi
I'm working with the following products to develop a product and have chosen to use a IDE based around Arduino and Visual Studio Code. This iDE along side off the shelf...
