Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi
I am writing an application that requires bonding/paring stuffs and face a problem as below
The maximum bonds that my device can manage is 2. When these 2 slots are...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
Dear Support,
we have done some technical question
About the N5 module of Dynastream (with nRF51422) we would like to program the software placed into the application...
my android program add many nRF51822 devices mac adress to a file in my android device.So I can count number of connected nRF51822 to my android device with bluetooth low...
Hi,all.i want to integrate ble_dtm(6310 board) to ble_proximity(pca1001 board).Can someone give me advise? i run ble_dtm on my board,and cannot find "Nordic_DTM" when i scan...
Hi,all.i want to construct our product test system.i follow AN34 page6 (figure 2) to do this.i have a question: DUT and nRF DK module run same firmware ? if correct,when nRF...
Hi,
In my application, I would like to take some action, when the bonding is removed from the phone.
At the moment I'm using static key for bonding and I see that BLE_GAP_EVT_SEC_PARAMS_REQUEST...
I'm using SDK 7.1, SD310 2.0.1, MCP 3.8.0.7
I have two versions of a board with the nRF51. Some of them have the 32kHz crystal and some don't. In my application I have...
Hello,
I am working on an application based on the "Motor control example". However instead of just setting two different values for the duty cycle I am trying to either...
Hello,
I have started to study your UART to/from BLE sample but after reading the following post ...
devzone.nordicsemi.com/.../
... I have a big doubts.
Due to...
Dear Nordic,
I am using a pretty much unmodified version of the BLE HID Keyboard example from the Nordic BLE SDK (straight of github).
I only modified pins, and disabled...
In Short: How to get status wether noticiations are enabled or not? Where is this stored?
Hello,
I would like my peripheral to start/stop a timer that does measurements...
