Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
We have developed a hardware platform using the NRF5340 on Nordic's zephyr (version 3.5).
Our current consumption in idle mode is still around 330 µA, instead of the expected...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Hi, I'm working on the DK for nrf52832. I have a working code for BLE, and another working code for die temperature using interrupt. Now I want to merge them and trigger the...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
We have an nRF52840 device that is required to do continuous BLE scanning in central role to find nearby advertising beacons and is never required to establish a connection...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hello,
A quick question about using an nrf9160 (+ sdk 2.5 - modem 1.3.5)
When I activate the following parameters: # LTE-M (LTE-CatM1) CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_NETWORK_MODE_LTE_M_GPS...
Hey,
I have been using the FOTA download client library with bg95 module for HTTP dfu for a while and works perfectly fine.
Now that I have added a few additions to my...
Hi,
I developed a custom board with nRF52810. Here is my schematic:
Layout:
I can succesfully upload the "ble_app_beacon" example in SDK17.1.0 with softdevice112...
Hello everyone, I hope you can guide me in a right direction. 1. I setup my environment as per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html , using...
Dear support i have two problems,
In ncs 2.6.1 i get: error: '__device_dts_ord_DT_N_NODELABEL_red_led_P_gpios_IDX_0_PH_ORD' undeclared here (not in a function) in the...
Hi All.
I am trying to emulate a central BLE module to scan peripherals around, using an nRF52840 USB dongle and nRF Connect for Desktop. The goal is to confirm that my...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
Hi,
I'm trying to implement a Firmware Erase and Update procedure using the nRF52832 module on a custom board. In the Nordic Devzone I've been following the steps to do...
