Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have a PCA10028 board. When I connect it to a computer the LED LD5 doesn't turn on at all, and no new USB connection pops-up in my computer. But when I connect it...
I found this website.
link text
curve is shown below.
There are app_utils.h information below.
@brief Function for converting the input voltage (in milli...
Hi, this is kind of a basic question.
So please forgive me if this is too easy...
This picture is from nRF51822_PS_3.1.pdf.
Also these pictures is from the...
I am trying to use a differential antenna with the NRF51422 and I do not want to misunderstand the datasheet. It says that the optimum differential impedance at 2.4 GHz seen...
If, how can I change the order of the descriptor? I would like to have the user_desc at first.
Most likely by changing their UUID but how to do that? I can't find any trace...
Hi every body,
i try to use 10 bit ADC resolution instead of 8 bit in the ble_uard_adc example, the problem is the ble_nus_send_string is configure to 8 bit, how can i...
Before I order the NRF51-DK I want to make sure, is it possible use it to program other nrf51822 modules? Can I use the Segger on board for flashing firmwares on other modules...
Hello,
Let me first try to describe my whole project I just started with today (Hardware just arrived).
I want to use the nRF51-DK as a central device to handle 4 peripherals...
I have these nrf51822 modules, bought them from this company Wireless Tag , it's a chinese company I guess but I just noticed that the modules only have a single 16 MHZ oscillator...
I using github code.
SDK is 7.0.1
SD : S110 7.1.0
Channel : 4 ch
Period : 20ms
Width : 1-2ms ( RC )
Sometimes the width operates at 18-19ms.
ex : PWM2 was...
I'm working with the ble_app_hrs_s110_with_dfu_pca10028 (nRF51 PCA10028) example and am wondering what will happen if I attempt to send more than one sample at a time. Will...
It looks like APP_TIMER_INIT changed in v8 of the SDK. I do NOT want to run the code for timer callbacks in the IRQ, I want to run in the background loop. How should I properly...
Hello,
Our application board uses two NRF24L01P and two microcontrollers, so we have total four quartz generators on board. To simplify things we would like to use a single...
