Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
i am working with eclipse. i want to create a binary file. after successfully creating the .elf file eclipse displays a make error saying region ram overflow by so and so...
Hello,
If I enable POFCON at 2.1V threshold in my S/W, build and download it in my target, and I turn on n51822 at VDD is 1.8V. That is, VDD is lower than POFCON threshold...
Hi ,
Could anybody share me the details on the time taken by the nRF51822 to comeout from reset state for the below reset input.
Wakeup from OFF mode reset
Pin...
Hi...
I started with S130 demo example code. Added a custom services . The problem I am having now is that after I connect ble_evt_dispatch isn't being called.
I have...
Hi, I have purchased a Nordic nRF51 and start to write my firmware using mbed OS compiler. As far as I can see the whole process was working perfectly. I could update the...
Hi,
I have a BLE peripheral with a custom service (using a different chipset). I'm working with S120 as a central, and attempting to read/write various characteristics...
I have previously bought a Evaluation kit, (now obsolete) and registered with it. I have also designed a new custom board with version 3 silicon, but I cannot download v8...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
How to flash SoftDevice and Bootloader (OTA enabled) to nrf51822 by CMSIS-DAP programmer?
For instance: I did cmsis-dap programmer with mbed code form github.
Can I do that...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
I know this was asked before, but none of the posts address my problem. There is a similar thread , but the issue on that one was that the softdevice was not being used. I...
