Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi,
Got stuck on an issue that has come and gone and then working fine, and are now back again.
I use a nrf51 module with the led-button-service example (sdk 5.2). It...
So, we are pretty far along in development (I have inherited the project) with an nrf51822, SDK 4.4.2 and SoftDevice "6.0.0-alpha". We are nearing release, and I was told...
I have set the POFCON to enable the power failure comparator and set the voltage level to2.5 volts. How do I know when the battery voltage is below the 2.5 volt level? How...
I want to try a UART communication without RTS & CTS
my board is PCA10001, and I use the SDK 6.1 example: uart_example.
I use Serial Port Utility to communicate with the...
Using SD_110 v6 I get a hardfault on the final call to sd_nvic_EnableIRQ(SWI2_IRQn);
sd_softdevice_enable before that returns success. Any idea why enabling interrupt could...
Hi,
I'm trying to implement an existing proprietary protocol on the nRF51422 SoC. In this protocol the device address is placed differently in the frame than the predefined...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
