Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Based on the ARM documentation for the Cortex-M0, the hardware can be configured to have a single cycle multiply or a 32-cycle multiply. How is the nRF51 configured?
infocenter...
For the transmission power, are we allowed to use any number in the range [-30, 4] or only the values specified in table 37 in the product specification ? When we select one...
I have a service a writeable characteristic and I'm finding the following issues.
Characteristic is read/write, not variable length, size of 4, no read or write auth, no...
I'm implementing a custom service with one characteristic and 128-bit UUID.
I am able to set the custom base UUID using sd_ble_uuid_vs_add() but the resulting bytes look...
Hi,
I would like to know can i configure advertising interval for more than 10.24 seconds.
Which are the functions i can use for configuring advertising interval.
Also...
Hi All,
Yesterday while (unsuccessfully) trying to get my dongle to work with Antware II, I did something I'm not sure what it was, but has caused the following:
MCP ...
I'm developing application on nrf51 for that i'm using...
SDK : nRF51_SDK_8.1.0_b6ed55f
Board : PCA10028
I'm trying to run code from SDK examples C:\nRF51_SDK_8.1.0_b6ed55f...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
every time I try to add a new example in Keil microvision, it dont work me.
last time I try to import a new pack, I got this error:
pack instalation failled...
I use SD 7.1.0. My own app works perfectly. I use my own PCB, debugger J-Link Segger.
I try to upload any app via bootloader from SDK's example (modified in LED_pins dfu_dual_bank_ble_s110_pca10028...
I'm trying to send over a ble the data for a tablet
I'm trying to use the example of analogues (NordicSemiconductor/nrf51-ADC-examples) an old time I get error response...
Hi,
While calculating the power consumption according S110 soft device specification only ION current has been considered.
So does ION include current consumed by DCDC...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
