Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
i'm confused of the relationship of wirepas and ant+,both claim to surpport mesh network and multihop.what's more confusing is that both are promoted by nordic.
I look up...
I find in the following example code that if I start my application from a powered-off to a powered-on condition and main() executes the code as shown, everything works fine...
Hi,
I do receive undefined HCI errors in my disconnection handler. I wait for the BLE_GAP_EVT_DISCONNECTED event and use the bleEvent->evt.gap_evt.params.disconnected.reason...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
Hi,
In my project, I need to periodically perform some jobs on the nRF51822 Beacon kit (sdk 7.1). For that, I think I need to use timers. However, I'm not sure how to do...
Hey everyone.,
I was trying to use nrf51822 as spi slave and just a heads up to know that i use Nrf51822 as master. I see that when chip select CS gets low SPI needs to acquire...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
