Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi, I'm working on a project and I need the GPIOs to have 3.3V available when the nRF52840 is in deep sleep, in order to use wake-up on GPIO. So I'd like to know what the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
normally, I would set the CMAKE_BUILD_TYPE to `Debug` to enable Cs "assert" function (not define NDEBUG). Zephyr (and Nordic-Zephyr as well) has the `CONFIG_ASSERT`...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
We are currently working through Exercise 5 – FOTA over Bluetooth Low Energy using the nRF5340 DK and encountering an issue where the mobile application (nRF Connect for Mobile...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hello, guys, I am working on distance measurement project using two nRF5340DK (nrf_dm sample application). I found duration for which the distance measurement between two...
