Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I got the nRF51822 DK and tried hooking up the dongle. I am using Windows 7 32 bit. When I plugged the dongle into a USB port, there is a “JLinkCDCUARTPort（COM19)” added to...
Hi,
My device is always in bootloader mode, even if i flash the sample heart rate application it is not entering into the application. Actually, before it was working fine...
Hello,
I am planning to develop an application in which I need to do some image processing (probably using open CV libraries), and I would like to know if the nRF51822...
I see in the example code there is
#define FLASH_PAGE_SYS_ATTR (BLE_FLASH_PAGE_END - 3) /**< Flash page used for bond manager system attribute information. */
#define...
I'm using NRF51822 and I have some question about the ble connection:
according to BLE 4.0 spec, when Tsup(connection supervision time) reaches, connection lost is considered...
Hi
Do the latest sample apps (for example, Heart Rate) which do not required bonding behave as follows:-
make connection from iphone
enable notification
check...
We have done some test on how fast we can receive data from a BLE service, which is around 6KB/sec and this is all fine. This test was fairly easy to make, as we could just...
I have implemented my own I2C driver and I am getting issues with NACKs.
On review my code is doing what twi_hw_master.c is doing.
I then went looking for a Nordic sample...
We have developed and certified a module which uses the nRF24l01+. We spent a good amount of time tuning the antenna circuitry which has resulted in very good range... in...
Hi,
how to get into the bootloader mode without pressing any button, when some application is running? I also tried it with setting the NRF_POWER->GPREGRET but it is not...
I am looking for a minimalistic schema design using BLE for collecting data from i2c (twi) sensor and sending them over blue-tooth to the receiver. I need the following features...
Hello,
I would like to know if there are any restrictions in the amount of external memory (RAM, Flash) that can be added to a system using a nRF51822. In that case which...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
