Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
How to enable the notifications or indications? In APP? can I enable it in ble peripheral?
I meet a chip of "Quintic" can do this. When I connect it to MCP and I get this...
I made Pwm program with 3 channels without using softdevice and without using interrupts at that time it is working perfectly. But when i am trying to use softdevice with...
Sometimes I receive pipe error 0x92 when I try to send a message from nordic to Android. What could be the causes for a pipe error 0x92?
I saw this: "Pipe Error Event ...
Hi,
I purchased nRF24Lu+ modules on ebay. I am trying to talk to them over USB from a linux machine.
Nordic datasheet states:
VID = 0x1915 and
PID = 0x0101
When...
Am I right in thinking that these security parameters are contradictory in that for the peripheral (nRF51822) to provide MITM protection, there must be either IO capabilities...
I just received my nrf51822 and am using an-36 as a starting point to build my first "Hello World" application for BLE.
All I would like to test is to have the status of...
I am trying to only perform calculations for connected ble services.
I am implementing a state machine that monitors the ble evt.
I use this for example when to perform...
hi guys,
I add a temperature service with one characteristic to notify the IC temperature in hrs example. But when enable hrs notify, SoftDevice crashed every time. That...
Hello,
We are using SDS 6.0.0, SDK 5.2.0 on an nRF51822. Our application is a data logger that can collect up to 128Kbytes of data. Users can connect to the data logger...
We did set the perform bonding option in the proximity example in the v6.0.0 sdk to 0.
And it did work. No bonding information is stored. Android devices are fully capable...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
I want to read the RSSI in an nRF51822 even though I'm not expecting to receive any packets… In short, I want to scan through every channel and read the RSSI on that channel...
HI
In the case the keyboard miss the LTK（or bonding info）, how can I start a reconnect or re-authenticating to let the host and device to generat a new one?
When I replies...
I'm using the nRF51822 as SPI slave. My CSN is of wrong polarity (active high). Is it possible to change the settings in spi_slave.c to make it work anyway?
