Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I am attempting run the rf test from the bootloader. But I have the following problems.
When I try to compile the dtm rf test into the bootloader I run out of space.
...
Hello,
I am using the nRF51822 Development Kit and nRFgo Studio Version 1.17.03211.
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v6.0...
Hello,
I'm starting a new project based on nRF51822 and I'd like to configurate the bluetooth to be appeared and allows the communication managment ( I want to creat two...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi All,
A simple one,, I just downloaded the master control panel app for android in android 4.4 phone.
My question is how to do bonding and how to delete bonding info...
Hi All,
I am testing the functionality of NRF24L01+ and for my purposes I have configured it as PTX, No Auto ACK.
I am able to communicate with the chip just fine and...
I am trying to send continuously sampled analog input using NRF24LE1 using Shock burst,The transmitter is not working while trying sample continuously.please help.
code included...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I'm designing an application where both, BLE and Ant should / could be used. I tried to download the S310 SOFTDEVICE from www.nordicsemi.com/.../nRF51422 . I'm asked...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need a low latency stereo digital streaming device and the model (nRF24Z1) is going to be discontinued.
Has Nordic a replacement for nRF24Z1?
PD: i need stereo, so...
In our product we have both a DFU profile and an application profile which is confusing Mac OS X 10.9 "Mavericks" since it caches device services unless it receives a service...
Hello,
I'm a new developer on nRF51822 and I'm trying to make a program that allows the nRF module to communicate with a glucose meter and a Smartphone application. My...
