Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Is there an example for sleeping? I just want to put this thing to sleep drawing minimum current and have it wake up on a RTC timeout, but do not seem to be able to achieve...
As indicated in the PS, System On Mode idle draws only 2.6 uA.
Does this mean that if I install and active a timer interrupt, where the interrupt routine places the system...
Hi,
I am new to ARM development. We are thinking of ordering mkit for evaluating and developing a custom BLE service(profile) which sends data to BLE client (probably a...
Hello Everybody!
I have been working with BLE security and I have an issue with OOB setup.
I'm setting my nRF with the following:
m_sec_params.timeout = 30;
m_sec_params...
I was reading this press release:
http://www.nordicsemi.com/News/News-releases/Product-Related-News/Single-board-Bluetooth-Smart-Arduino-solution-is-low-cost-and-can-be...
Yo!
I'm very concerned by what I hear about Bluetooth Low Energy security. According to this guy , who presented a paper on the subject at a USENIX conference last year...
Any experiences about analog sensor LM35DZ? I used this example: main.c
The LM35 data sheet says it will operate from +4V to 30 V supply. I'm use supply only Vcc pretty...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I'm using API 2.1.3 and I'm having problems with SendData blocking forever at the end of a process. I placed access mutexes around each method call to the library, as well...
Dear Nordic Developer Zone,
I have modified the ble_conn_params.c file in order to be able to negotiate new connections speeds between IOS app and Nordic nRF51822 chip...
Hi,
Regarding the bond_info_store() routine, I am having issues where after several calls to this function (client pairing forget/reconnect), my p_bond gets corrupted. This...
Hi, I am developing a BLE application using SPI and TWI. (Using nRF51822)
This discussion is about my survey in development zone for future develop the TWI part.
I want...
I'm calling ble_bondmngr_bonded_centrals_store in response to BLE_GAP_EVT_DISCONNECTED as is the case in plenty of sample code, but when ble_bondmngr_bonded_centrals_store...
