At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I am using nRF51822 with Softdevice S110 v6.0 to advertising packets and I would like to know when transmission is over to read some data from external sensors. I tried...
Hi, im implemented several services and characteristics in the nrf51822 with S110, its all working (read, write and notification), tested with an iOS app.
Now i need to implement...
Hi,everyone
I want to make out 4 channel PWM with PPI and two timers , PPI configuration like this,
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer...
Hi All,
I would like the nrf51822 sleep, wake up and then continues advertising.
I try following code:
NVIC_DisableIRQ(RTC1_IRQn);
NRF_RTC1->EVTENCLR...
hello, everyone.
i am a new, i can't understand the meaning of "One event can trigger multiple tasks by using multiple channels and one task can be triggered by multiple...
Please provide me some details about how to implement watchdog functionality so that i can reset the entire system for avoiding software Hangs
I have come up with a code...
Hi,
I have downloaded the SDK 6.0 which contains the ble_app_uart and tried to compile it using GCC, but getting the following error which doesn't make any sense because...
I see the nrf51822-DK and and nrf51822-EK are now marked 'not recommended'. Why is this?
I now see an nRF51-DK and an nRF51 dongle. Are these now the current development...
Hello,
I want to use broadcaster mode for nrf51822, could you tell me please what I must to do to use this mode?
I suppose I must to set BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hi,
We need to develop piconet where each device able initiate receiving and transmitting data.
According to a Bluetooth Core V4.0 specification this topology named like...
Hi Nordic DEV Team,
In my application, I would like to use sd_flash_page_erase to erase like 100 pages user data; the problem of pstorage is that I cannot specify the page...
I am connecting my development device acting as a BLE keyboard using HID over GATT and it seems to be draining the phone battery very quickly. Every 7 seconds I would get...
I am using a US-100 ULTRASONIC SENSOR MODULE, and I need to measure the pulse width that this sensor produce. In arduino we can use a metode called "pulseIn", that gives you...
Hello-
I'm trying to load the Blinky example, I am using the nRF51822 Evaluation board.
I am able to compile but cannot load the board, a window with "Cannot Load Flash...
