Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...
Hi,
I have application where I drive LEDs with shift registers. I need to send 14 bytes via SPI every 200us while I am in BLE connection. Timing should be exact as shift...
Hi,
I have a project where I need to communicate using UART BLE between nRF51822 and a PC (MS Surface Pro 3) with Windows 8.1 and embedded BLE hardware.
I have programmed...
Hi,
I have downloaded nRF51_SDK_7.0.1_1d6e5cb.zip and run nRF51_mdk_6_1_0_installer.msi
Neither zip file nor created Nordic Semiconductor/nrf51/ folders have ewp or icf...
Hi,
I think it's a simple question. I want to connect a micro to communicate with a phone via the nrf8001. I ported everything thanks to the guide that you posted (for...
Can we use the tx_complete.count given with BLE_EVT_TX_COMPLETE as an indication on how many packets were sent out from the last ended connection interval?
thank you
...
I have a custom board utilizing an RF51822aa device. To test connectivity to the board I built blinky_s110_pca10028. Using Keil 5.12 I tried to debug the program simply expecting...
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash Download...
where can I get working sample code of nrf51822 with nrf24l01
including code of nrf51822, and code of nrf24l01, both TX, and RX.
in my application, I need 518 to RX data...
I am working with a university project where need to connect up to 20 wireless sensors together with 1 master, which will be communicating with either a computer or smartphone...
I found a IAR project at dir [nRF51 SDK_v4.4.1.31827\Nordic\nrf51822\Board\nrf6310\ble\ble_app_hrs\iar].
But my IAR ARM IDE(ver 6.60 newest) don't support nRF51822.
Do...
