Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
developer.nordicsemi.com/.../a00969.html
I'm trying to understand whether this can be called in a timer interrupt ( app_timer ) and how frequently. I seem to have a bug...
I have nRF51822(pca10005), Dongle(pca10000)
And DownLoad Keil, nRF Tools, nRF Studio, nRF SDK, Sniffer, wireshark.
I try to run the example
C:\Keil\ARM\Device...
I am debugging the bootloader to work with a custom board. I have the bootloader project open, no application programmed, s110 softdevice programmed, and the hexfile for the...
I want to use app(nrf uart 2.0)
so, I try to change UUID,
but I don't know how make custom uuid and use it
and I don't find function(ble_cs_init())
hlep me, p...
I just tried compiling this for the BLE nano and it explodes to a 245K download (much too large for device). I've also tried including only the headers (DigitalOut and wait...
Hi,
I purchased Nordic new reference platform nRF51-DK(pca10028) and try to work for DFU OTA.
In my test, first of all program S110 V7.1.0 by nRFgoStudio and downloads bootloader...
Hi
In a bit of an over-enthousiastic mood, I bought 3 pieces of the nrf51822 beacon kit, and the, as this did not gave me download access to the NRF51 SDK, bought a nRF51...
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
