I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
I am working on a project using the nrf9160DK for initial firmware development. Trying out the SAADC i encountered that the measured values were always about 20% lower then...
