Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hi,
I just got an Arduino and a BLE shield. I was following the Smart Starter Kit. The demo project have me errors, so I just started using the proximity example, and editing...
Hi,
I am using the nrf8001 module provided by adafruit ( www.adafruit.com/.../1697) but it's not clear if the RDY and REQ pins available on the chip are active low or not...
I have made a small device composed by
SD310-1.0, boootloader and application. The device is sealed to be waterproofed and has a serial conenction used by the custom bootloader...
I've been working with SDK 7.1 and I am struggling to understand how to get the makefile working with an NRF51822-QFAA device rather than a nRF51422-QFAC. I have samples of...
Hi all,
I did this upgrade hoping to have a TX_COMPLETE event issue fixed (I'm not able to send more than 1 buffer per connection it seems in my notification based service...
Hi,
There are two advertise nodes, only broadcast (one packet/s) . The S120 star scan. At the beginning everything is OK，but after a while, maybe 3-5 minutes, only one...
Dear all,
I've loaded this example github.com/.../Blinky_ble
into the nrf6310 as it is, and s110_nrf51822_7.0.0 as a softdevice
I am connecting to the module through...
I need the nRF51-DK-HW hardware files ，but without a product key.
And I cann't buy a nRF51 in CHINA.
Someone can give me a product key or
help me to buy a nRF51.
Thanks...
Hello everyone,
I have developed a firmware that makes accurate time of flight measurements, working with my own protocol.
Now I need to integrate this firmware with BLE...
Hi,
We would like to switch to a stand alone debugger for nRF51822, However in the product specs ( www.nordicsemi.com/.../nRF51822 ) mentioning that standalone programmer...
Hi guys,
I have nRF51822 Evaluation Kit.
I am trying to make simple project for my senior design.
Here is the setup.
I need to control simple on/off switch from...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
Hello,
I need to send packets on a specified advertising channel and receive them at the same advertising channel. Unfortunately, the SoftDevice API does not seem to support...
