Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi team, We’re using the STM32H7 as the host MCU and the WMC02C Wi-Fi module (based on the nRF7002) connected via SPI on a custom board. I tried running the Wi-Fi scan example...
Hi,
I'm attempting to upgrade an existing project (which is still in the development stage) from NCS 2.7.0 to 3.0.2; this seems to break native TLS, and I'm not sure why...
Hi, I've encountered a change in behavior when upgrading from NCS 2.9.1 to NCS 3.0.1 regarding MCUboot and watchdog integration. In NCS 2.9.1, I was able to enable the watchdog...
I'm developing a custom board with nRF52832. We developed a flexible circuit for NFC antenna, and tuned following the indications on this post on the Nordic blog. Actually...
Hi,
I'm a beginner. I downloaded nRF5 IoT SDK, and tried to run and debug the application "publisher" on nRF52 platform. And each time, I got a message "no source available...
This is what we get from JLinkExe:
Found SWD-DP with ID 0x2BA01477
Could not power-up debug power domain.
Can not connect to target.
This all happens when we use P19...
Hi, i use softdevice 9.0 and s110 8.0.
I want to make 38kHz pulse.
so i tried to use nrf_drv_timer and gpio.
if i try to make 200us, it worked not bad.
but when...
Hi, everyone.
I have read the nRF5 SDK --> GPIOTE part in the infocenter. However, I have not get anything useful.
I just want to recieve a interrupt from an external...
Hi all,
I have installed the 1.21.1.3 nrfgo stdio from nordic site.
in device manger nordic board is not detecting( both nrf51 and nrf52) only in my lap.
any setting...
Hi
I am working on customization of proximity device with nrf51822 and I need to lock it to first connected device (so after first pairing I have to make blocking connections...
I took the reference of your example and instructions hear -
devzone.nordicsemi.com/.../
The program runs but get struck at sending the I2c write command .
Do I need...
Hi,
just want to make sure: is it possible to merge UICR values into hex so that I can load some values there during production in a single flashing stage?
thanks
best...
I now have my app.hex and bootloader is running at nRF51822 and yet, the nRF Toolbox finds "DfuTarg" as expected. However, after selecting my file the UI surprisingly starts...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
I made "radio test" program as below at the first.
void radio_tx_carrier_test(unsigned char freq_ch)
{
NRF_RNG->TASKS_START...
Hi,
Can we add device address with all fields set to zero's to whitelist.
I went through the spec, but it doesn't talk about the address set to zeros.
Thanks,
r...
Is it possible to change data send in scan responses after each Advertising Event? I know that sd_ble_gap_adv_data_set() has constant input arguments, but it seems weird for...
