Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am using the nRF51822 and code base 6.1
How can I program the advertising mode of the beacon to not time out. I am looking to advertise for 10 seconds and then go to sleep...
When I downlaod and program the softdevice version 6.2.1 via nRFgo Studio, it shows Softdevice version as S110_nRF51822_7.0.1 after programming.
Any idea why actual version...
i use nrf51822 for my project, i want to do is when smartphone are pair with my module i store one flage in flash whenever user enter right security key and after reset i...
Hello,
I have purchased NRF51 MBED enabled board. I need some assistance in how to get started. I want to use the KEIL software and I am not able to.
I have downloaded...
I need a reference design of nRF51822 for minimum 1 meter range . The circuit will run from CR2032 battery for at least 24 hours and will take some readings from ADC input...
i am unable to sniff the packets between two devices once the connection is established between two devices..i am using nRF sniffer 1.0 ...
i am able to see only the advertisement...
Hi,
How can I control the PDU error code when reading an attribute.
E.g. Attribbute not found 0x0A. For more info see 3.4.1 Error Handling Bluetooth spec 4.1 Volume 3...
Hi,
I have created a custom PCB that more or less follows the Nordic SmartBeacon design: Beacon_V2.pdf
Instead of BAL-NRF01D3 I used the BALF-NRF01D3 as this is supposed...
I have use random number generator in S110, the source code just like:
uint8_t num_rand_bytes_available;
err_code = sd_rand_application_bytes_available_get(&num_rand_bytes_available...
what does it mean the VTG led turn red ? but it has no bad effect to my project. In addition, I find a strange phenomenon. I use three 1.5v battery to power my board. The...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...
