void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi all,
I have read the nRF51822_PS v2.0 and know that nRF51822 supports the SPI slave mode,so I want to know whcih version of the chip will support it?
Also,I have...
Hi,
is possible to reprogram flash in nRF51822 via radio channel?
If yes - is there application note for this feature
Some customer want to secure upload firmware without...
Hello, I need to transmit a data packet with hundreds of bytes, but aparently the S110 SoftDevice can't handle payloads with size bigger than 23 bytes.
According to the...
I load battery_demo_nrf8200.hex into nRF8200. I can then read battery data on Master Control Panel and watch data change when I change VTG.
I then load health_thermometer_application_nrf8200...
We need to customize the Gazelle protocol on nRF51822. To that end we will need access to the protocol source code - not just the API. Is it possible to progress this way...
Hello,I have a ble HID device,
it can connect iphone4S/Ipad with IOS 7 system,
but the function button of (page up /page down) can't work in app wps ppt.
but it can work...
hi guys, i am writing a TWI application along with S110 but i am not getting the proper value from the sensor which is TWI interface, is anybody wrote an application, kindly...
Hi,
We have a custom board with nrf51822 and we use chip antenna from ST BAL-NRF01D3, now the distance it support is very very short (less than 20 cm). So, please tell me...
Hello,
Can I assign two GPIOTE tasks to work with the same output port? One to set it high, another to set it low.
Here is the code segment:
nrf_gpiote_task_config...
Thanks for all your help.
From 30-yr programmer and new bit-banger.
Playing with the 6310 example, rtc_example, the following code makes no sense to us with the toggle...
I have just begun tests with the nRF51822 DK.
I have written a test program which uses the RTC and PPI to generate an event every 125 ms, and use a task to toggle a GPIO...
Hi,
I´ve programmed the nRF51822 DevKit´s module (PCA10004) with S110 SoftDevice and example <ble_app_pwr_profiling>.
In SystemOffMode I measure a current consumption of...
