I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
I'm trying to connect to a Raspberry Pi from an nRF52832 via BLE Central mode. The Pi is running a node.js app (via bleno) and I can connect and communicate with it...
i m using pca10028.. with gcc tool chain setup with sdk 8 in windows.....am run one ble_uart example and after 180 second my device goes to sleep.. and second one that i have...
I'm using the SAADC of an nRF52832. I'd like to reduce the error of my measurements from the nominal +/-3%. I'm calling the NRF_SAADC_TASK_CALIBRATEOFFSET periodically to...
Hi,
I am trying to use nrfutil to generate my verification key.
However in the bootloader the key has this format
__ALIGN(4) const uint8_t pk[64] =
{
0x6e, 0x76...
Hello,
I am trying to update my bootloader using DFU and I am running into a few issues. I have successfully flashed and tested my current bootloader on my board and everything...
I am using the nRF51822 in an application where I want to run the UART as fast as possible to communicate with a host processor. I have been able to get reliable communication...
I am trying to create a package file to use with the DFU on my design.
I followed the instructions for getting nrfutil latest version built and was able to generate a private...
I'm using an NRF8001 with an ATMEL ATMEGA 328P (the microcontroller from an Arduino). I need the microcontroller to go to sleep, but still allow the BLE chip to advertise...
Hi,
for development i am using gcc and makefile on osx.
I wanted to automate my makefile with the possibility to upload directly the hex file to my nrf52 devboard.
...
I'm using PPI to trigger a gpio high after a given delay from 4.00 ms to 8.00 ms. I need to be accurate up to .01 ms but i'm seeing some jitter in the actual delay vs given...
Hi,
documentation for NRF_LOG_RAW_INFO state that it is:
A macro for logging a formatted string without any prefix or timestamp.
But when I use next code snippet...
Hi
After building ble_app_uart in Nordic SDK with board pca10028 it gives some warning like
/usr/lib/gcc/arm-none-eabi/4.9.3/../../../arm-none-eabi/bin/ld: warning...
hello sir, i m using gcc tool chain setup in windows with sdk12 in pca10028... so can i useexample->peripharal-> timer example same as rtc ... i mean sleep condition same...
I would like to use the flashwrite function to store some data in the flash. There is an example in SDK 11.0/peripheral.
But I have a few questions about the example: ...