Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
Hi,
I am trying to measure the current consumption on my application, and measured some quite high values even after calling sd_app_evt_wait().
After reading through some...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We have sold over 8000 devices of our first product. Currently we are...
Hello,
My problem is to much current c.a. 40uA in POWER OFF mode. Below attach code:
void power_down()
{
nrf_gpio_pin_clear(22); // Wylacz mostek tensometryczny
nrf_delay_ms...
With nRF52832 DK I have managed to compile this blinky example:
#include <stdlib.h>
#include <stdint.h>
#include <stdbool.h>
#include "nrf_delay.h"
#include "nrf_gpio...
I am getting no radio (as in not being able to pick up advertisements packets) from my custom nrf52832 board. The antenna design is a hack so I am not looking fo stellar performance...
We are looking in to developing a generic class to connect and handle our BLE devices for use on mobile devices such as Android and iOS.
Now since we want to have as less...
Hello Experts,
I am running the following examples to test the DFU bootloader in gcc and eclipse environment.
bootloader_secure/pca10040(Bootloader) and experimental_ble_app_buttonless_dfu...
I found a problem of the nRF51822 in boot state.
Power on reset is not executed occasionally when used dying battery.
The problem occurs in the following steps:
...
Hi All,
I'm having a BTLE_CONNECTION_TIMEOUT when I connect the device in Master Control Panel 3.10.0.14 while the chip is not in debug mode.
The device connects without...
Hi
I am trying to upgrade the firmware in a BL652 using a Segger Jlink Edu.
The BL652 is powered with 3.3v using a regulator off the JLink 5v output.
I had poor/unreliable...
I am using a processor that can provide an 32KHz clock (from its crystal).
Can you recommend the voltage divider (caps or resistors and suggested values)?
I will power...
I added a task to ble_app_hrs_freertos.
The soft device was burned.
The address is in the default state. (RAM:0x20002128 ROM:0x1f000)
I reset the total heap size...
Hello i am quite new to using BLE for data collection. I am using a Readbear BLE Nano with a Nordic nRF51822 on it.
I want to read a Sparkfun MMA8452Q accelerometer's X...
Hello, if I disable interrupt on nrf51xxx device, function sd_ble_tx_buffer_count_get will simply run right into hard fault handler, without returning anything.
I do not...
