Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi Everyone!!!
I am interested in nrf52832. I was going through its product specification v1.2 available over here: link text
At page no: 1, in the section: Key Features...
I have a nrf51 Dongle handy and I'm wondering if it can be used as an ANT+ to USB gateway for running simulANT+ on my PC?
If this is possible, where can I find the dongle...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1? About problem: It...
Hello, I find these structs:
ble_gatts_attr_md_t
ble_gatts_char_md_t
show up quite often in example projects. My qeustions are:
What are these? And when will I be...
I am using esb dpl in nrf5 sdk v11. I want to put a special packet in ack payload. but I think nrf_esb.c code can not do. the reason is that when on_radio_disabled_rx() is...
Hi,
I am developing a printed circuit board for myself using a NRF52 and I am unsure how to actually burn a bootloader program to the NRF52. Additionally, once the bootloader...
Hi All,
my device wakeup from system off casued from reset RWOFF, I read the register RESETSRC and byte E is 1.
maybe there is something about the configuration of gpio...
Hello,
I was reading about that 6LowPAN is being used in the IoT SDK.
I have a few questions about this.
Can the 6LoWPAN node communicate with another 6LoWPAN node...
Hi,
I am working nRF51822 communication. I am using nRF peripherals examples in SDK 11.0 series.
I would like to know the sleep mode examples in communication like after...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
