Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Did anyone manage to build project on Eclipse with some nRF52 BLE application for HomeKit?
I have found only one project from aanon4 but I cannot even build it.
Sometimes...
Hello,
I am thinking of creating a project that I intend to manufacture that needs to operate 10 dc motors via Bluetooth.
Would this be a logical and cost effective...
I am using nrf51822, I have two firmwares with different offset address, one is having offset address of 0x16000 another at 0x28000.Both are 60kb of size each. I want to start...
Hello all,
I try to find out how long some configurations of the Enhanced Shock Burst protocol take time. I am working with the nRF52 Development Kits.
Some timings...
I want to combine two applications, both of them having two services. One application resides at 0x16000 and other one resides at 0x249f0. I am using softdevice 7.3 and sdk...
I am using nrf51822 and softdevice 7.3. I am working on the github mesh example. I want to add uart service with mesh, so that I can communicate with that particular device...
Hello, this is what I can think of when porting a project, but before that, a little background about my project:
it uses BLE (duh)
it uses uart to print test output...
Hello,
i am using the nRF52 Development Board with SDK 11 and I have trubble with the UARTE Interface with DMA. Parallel I have running the ESB protocol.
I know the problems...
hello there i want to add battery service and thermometer service in advertisement packet. so i changed in uart project. but in advertisement project i can see battery service...
hi
I used the nrf51 dongle to receive advertisement packet from other nrf51 dongle. I used this formule, d = 10 ^ ((TxPower - RSSI) / 20) , given from this link forums...
Using Command Line Tools 9.0.0 attempting to push code.
ERROR: JLinkARM DLL reported an error. Try again. If error condition
ERROR: persists, run the same command again...
Hi All,
I am attempting to use 6 PWM channels with the app_pwm library on the nRF52 and am only able to successfully get 4 pwm outputs. Upon changing the 6th channel (PWM2...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
