Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
I have the NRF51 DK working with CrossWorks on OSX. I have the blinky example working.
Now I would like to figure out how to get very basic HELLO WORLD type demo to iOS...
I am implementing dual bank DFU on the PCA10001 board using the latest SDK (7.2.0) and S110(7.1.0). I am able to enter bootloader from my app as detailed here:
developer...
I'm just reading the documentation regarding the analog digital converter and wonder why there is one bit in the configuration register for every analog input. What will happen...
I'm using a relatively large GATT db that has rd_auth and wr_auth set to true for every characteristic. This prevents the stack from automatically replying with cached values...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
Hello,
I have some questions about the DC/DC conversion factor in nRF51822.
In the datasheet nRF51822_PS v3.1, Figure 11 shows the graph about conversion factor...
I would like to change the device name of the nRF51422 trough a mobile device(Android AND iOS ). The name should be stored even when I disconnect the supply.
From a nordic...
Sir,
We designed a prototype card including "rfd22301" containing nrf51822. We will use in mass production directly the nrf51822.
We will use the BT as a transparent UART...
Hi, I try to transmit mp3 or wave file.
and I am using nrf51822. Is it possible?
I know that people usually use the A2DP profile, When they send a music or video
...
I'm running example apps from the SDK on a PCA10028. When debugging in Keil uVision, I find that I can only stop the code once. The second time I try to stop the code I always...
Hey All,
I am working on a project that involves a Redbear Labs Blend as a sensor platform, then transmits the data to a dfrobot Bluno over nRF8001 BLE. I'm still new to...
The release notes for S110 v 8.0.0 say .
The SoftDevice Specification corresponding to this release is the
S110 SoftDevice Specification v2.0.
I can't find...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
