I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello everyone!
I'm writing here becouse I'm quite new to the embedded world and I'm experiencing some troubles starting with this platform.. I must say that, since I found...
Hello,
In my application, I'm going to power the custom board with a fixed 5V connection. What is the best practice for powering the nRF51422 IC? I was thinking in using...
Hi.
We need to ring the Buzzer with 4.2kHZ PWM.
However, in the event of 4.2kHZ in nRF51822 PWM is inaccurate about 2us.
Please tell us how to fix it.
※link Very...
I use this step-by-step guide to run nrf51 Iot SDK example on nRF51822.
First I modified app_ipv6_coap_client_pca10028 such that I can run it on nRF51822.
I downloaded...
Hello Everyone,
Im using the NRF8001 for my application and was looking through the arduino SDK provided by nordic.
I want to run the device in UART mode but do not...
Hello!
I have been trying to figure out how to get the device ID/MAC address for the NRF8001, and I found the lib_aci function lib_aci_get_address() that calls a cmd event...
Hello!
I am using the nRF8001 BLE chip on the Redbear Labs Blend board, and I need to get the MAC address, which I heard is also called the device ID. I understand that...
Hi,
I am new to BLE development and I am currently using nRF51822 with the soft device S110. I am using the example ble_app_hrs that includes the ADC converter. I would like...
Hello,
The max TX power for nRF51822 is +4dBm and it corresponds to Bluetooth Class 2.
Is there a possibility to use an external amplifier to increase TX power to meet...
Hello,
I'm trying examples supplied with SDK, running on pca10006 with nRF51422 chip board and Segger J-Link debugger.
I am able to
Erase entire chip with nRFgo...
Hello,
We're creating a new design with the nRF518122 as a TWI master to two separate I2C busses. No SPI devices of any kind, so I don't think there is a resource sharing...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I need to store few variables values(long a = 4568;) to RAM (might be some other place) when the system went to sytem off mode .
How I can achieve in the nRF 51822...
Hello.
I have to detect presence of several nodes (max.8, battery supply). Addresses each of them will be known by master device. I don't have to send any data from central...
