Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Hi
In my project, we wanna transmit large amount of data from UART master to nRF5182, and then to iOS7. Baud rate is 19200. Feed-in speed is near 2KB/sec. BTLE transmission...
I am trying to use this android app to read/write values from my nRF8002. Every few seconds I get a request to bind to the board, even if I already accepeted to bind to it...
I have a example using nRF24LE1.
So. I want know what can I change that example. or how to I get nRF24LU1+ example.
nRF24LE1 example is this.
/* Copyright (c) 2009...
Hi all!
I got a little problem with my ble device.
That is: my device takes system_off mode as initial mode, when being pressed the button, it will wake up and start advertising...
I am using UART0 for wired communication and S110 for Bluetooth LE communication at the same time, using HRM profile. System seems to work as expected, I get log output from...
I am using the nRF51822 to communicate with a HRM (and nothing else), but I intend to use the power of the ARM to control other sensors and process the received data. I use...
Mother board :6310
IAR: IAR Embedded workbench for ARM: 7.10.1.6735
IAR Embedded Workbench common components 7.0.2.3053
Softdevice: S110_nrf51822_6.0.0
sample Project...
I am able to debug in windows using uVision, and now I port it to use eclipse in mac,
however, I am getting GDBServer will be closed error, anything clue what did I do wrong...
Hi,
I am using Nrf51822 custom board.
i want to store Nordic temperature value for every 15 minutes .
i dont want to use polling method.
Kindly suggest me how...
Hey folks,
I am currently trying to use my nrf51822 evaluation board as a beacon. This is working pretty well but I need to have it broadcast its current battery level...
Hi,
I am using the following security level for my nRF5188 device.
BLE_GAP_CONN_SEC_MODE_SET_ENC_WITH_MITM(&bas_init.battery_level_char_attr_md.cccd_write_perm);
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
I'm interested in minimizing footprint as much as possible for a project -- has anyone here used chip antennas with the nRF51822 that they can recommend?
The fractus chip...
I have taken your advice to use the nRF51822 for my current design commission, but a number of downloadable files are locked. How can I get access to them?
Hi
I have a module of nrf 8001 and i am successfully communicating with nrf 8001 low energy bluetooth chip. I want to know is there any security feature defined in the...
