I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello everyone! :)
I have a problem with LTE connection. It worked for a few months; however, since a few days ago, the nrf9151 refused to connect to LTE. I tried with 2...
I'm building a system with onboard stereo speakers that can take a maximum of 1,4A when operating at low battery voltage. Can I safely bypass the npm1300 and directly draw...
I am using nRF Connect SDK 2.9.0 with Toolchain 2.9.0 and trying to interface Winbond W25Q32 SPI flash memory with nRF21540DK (nRF52840) . I need help with the following:...
Dear Sir / Madam,
We are testing with NRF9160 and building on top of k _uptime _ticks, I find the precision of the ticks clock to be ~70 ppm, while testing on my desk. According...
Hello,
I have been trying to figure out how to enable coexistence between Bluetooth low energy and the nRF7002 and I have some questions.
1. In the nRF Connect SDK documentation...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
I would like to add smp ota firmware upgrade to the matter sample project, can you provide me with the specific steps to do so, and in which path is the ota file compiled...
Good night,
I installed the VS Code/nrf Connect in my Windows 11 Prof.
I copied the "blink sample" and I tried to build it, but I am receiving
* Executing task...
I am following this example https://github.com/crfosse/ncs_projects/tree/main/peripheral_zephyr , both secure and non secure and I am not being able of making the non secure...
Hi,
I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Hi
I see i get a cmake warning with DFU enabled with the following message:
whats the purpose of this? should i just have it always enabled in my conf, or for prod...
