Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
hi,
In my device(nr51), have multi service and one client.
when i initial the client first ,then to setup service. this follow is O.K.
But, if i initial the service, and...
Keyboard source: Desktop 2 v1.0.5
Dongle source: 1. Desktop 2 v1.0.5 dongle hex; 2. Desktop 1.2.2.293 dongle hex
I found it is very defficult to pair the keyboard with...
Hi,
1. I have some puzzles,please give me some explanations,thank you!
In my design,I use some 51822 devices as tags which can communicate with the host.
The tags can send...
Hi, I want to know what's the differences between the NRF_CLOCK_LFCLKSRC_RC_250_PPM_xxMS_CALIBRATION and NRF_CLOCK_LFCLKSRC_XTAL_xx_PPM where xx means a decimal number.
when...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi,
I want the NRF51 to respond to a received packet from a particular device using register TIFS to control the interfame timing.
For TIFS to work I have to set the...
Dear Nordic,
is it possible to build a simple data bridge at speed of 115200 and up based on nRF51822 with CTS/RTS support and a fixed pin code for nRF51822 pairing?
I am working on a multi-node network application with multiple transmitters and receivers and I have a question about timing for chips like the nRF24L01+. I would like to...
Hi
In my case i have gpio interrupt for every 25ms. so i change button detection delay t0 10ms.
and i given timeout in all while loops of twi_hw_master.c.
but my...
Hi,
we have nrf51822 custom hardware.
we are flashing application through j-link.
but after every flashing , i need to do switch off and on the device.
then only...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
Hi,
I need to send more than 500 packets(each 20 bytes) to the master for every 1 minute, through the timeout handler. But i cannot able send all the packets, btle_connection_timeout...
