Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello,
I have nRF9160, modem FW = 1.3.6 and nrf sdk version 2.7.0.
I am trying to create an outgoing socket with connects to specific port num and ip address but I am...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
Hello,
I'm using nRF54L15DK and nRF Connect SDK 2.9.0. I'm developing a project for PID control of the temperature of a peripheral, let's say a heater. The feedback is...
Hi,
Not able to compile hci_uart application on latest nrf-sdk Following is error :
test/zephyr=ZEPHYR_BASE -fmacro-prefix-map=/home/abhinav/nrf_latest=WEST_TOPDIR -ffunction...
When programming a nRF9151 firmware on to Thingy91 X, I made a mistake and failed to change SW2 from nRF53 to nRF91 (the label is very small). The USB serial port no longer...
Hi,
I have finished some code with nRF54L15 and nRF52833, now I want to add nRF7002 to my design and I am wondering whether this is available?
Thank you!
Hello, World
Please note that the following questions may be difficult to read as the text was created using a translation tool.
I have downloaded version 17.0.2 of the...
Hello Nordic Team,
I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
Dears,
I made custom board using nRF52832 and tried to write FW in flash. But I failed it.
*. HW JTAG : J-Link V9+
*. SW tool : nRF Command Line(nrfjprog)
Step #1...
I'm trying to run the 32 MHz SPI00 on the nRF54L15DK to communicate with the MX25R64 flash. However, the clock signal I'm measuring is limited to 8 MHz. Do you have any ideas...
Hi.
I am developing with NCS 2.7.0 using 5340 and have configured it to use 5 generic switches. These work fine. However, the order of the switches displayed in "Home" on...
Regarding the schematic for nRF54L15 DK I currently see on the site that the link to the schematic is disconnected, can you please provide the URL where the schematic is available...
