Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
I am failing to build any of the Matter, Thread or Zigbee for nrf52840dk with the following failure.
I successfully build a blinky and bluetooth app, so my tool chain...
I am trying to use fstorage with the sd backend (SDK 14.0.0). My issue is that, after successfully calling nrf_fstorage_write, the callback I registered using
just never...
Hello,
I'm developing a program on a NRF52840 DK in the SEGGER Embedded Studio IDE that outputs a PWM signal when a Bluetooth Mesh GenericOnOff signal is recieved.
I got...
Anyone knows why I'm getting this result? I'm building the application using sysbuild and flashing normally on nrf52840dk. I tried both following all the steps in the lesson...
Hi,
i am trying to create an Indoor Positioning System with the nRF54L15.
Currently i am able to connect 1 initiator to multiple reflectors simultaneously,
When...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
Hello,
I'm trying to run the NVS example on the NRF9160DK rev 1.1.3 with the on-board MX25R6435F external flash memory.
The sample runs OK as nrf9160dk/nrf9160 but the...
I'm working with the Matter Template example and creating a sensor monitoring device on the nRF52840 platform, and I'm developing on a Windows environment with SDK 2.9.0....
hi support team,
i have one problem for 54l15+7002 in ncs2.9.0
I am afraid that I need your help.
I was porting MQTT demo and PERIPHERAL_UART demo together and want...
I have a nRF9151 currently set up to observe a CoAP resource on my server. The initial GET request works, and if I respond with new updates from the server (within a few seconds...
Hi, guys. I encountered some software issues while using VS Code for development on the nRF5340 DK. During the build configuration, the code reports an error saying it cannot...
Hello, recently I bought the Seeed XIAO nrf52840 because I read in the datasheets the power consumption of the microcontroller is 400 nA typical in SYSTEM OFF mode without...
I am using VSCode with nRF extension with the latest 2.9.1 SDK.
I have been working on an application for bluetooth for the 54L15-DK.
I want to do a custom sensor driver...
Hello DevZone,
I have an nRF5340 devkit along with an nRF7002EK, and I'm looking to upgrade from SDK version 2.6.1 to 2.6.4. However, I'm facing an issue. In version 2.6...
