I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
We are developing a BLE application with nRF52833 512kB ROM size and using NCS v3.0.2. However it seems the ROM size occupied is not so logical, or the ROM size for NCS (Zephyr...
Hello,
I am having nRF9160 with modem FW = 1.3.6 and nrf sdk version 2.7.0
I am using MBEDTLS library for generating self-signed & CSR certificates with EC-Key and RSA...
I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
