I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hi,
My company has a product that is in production using the nRF5340 SOC. We noted this morning that the product would boot and application code even if the nRF5340's reset...
Hi Nordic Team,
I’m currently working on a project using the nRF54L series, and we are using a 32 MHz external crystal oscillator based on the reference design. On our PCB...
Description of the requirements
SDK:15.0.0
MCU:NRF52840
I currently have a product that is already in production, and I need to replace its boot program, and the new...
I am trying to flash a new board using a Segger J-Link Plus Compact. I use the same code to flash my nRF5340DK and it runs fine. I see the debug statements in the JLinkRTTViewer...
I'm working on a Thingy53 project with Zephyr RTOS that requires TLS connections, but I'm encountering persistent "Failed to create TLS socket: 23" errors (ENOMEM - out of...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
Hi,
Also asked your AI, but if I combine the information on https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/measure_current_source_meter.html with that on https:...
Hello Community!
I want to use the npM1100 as a power management device in my project. The external battery to be used is the ER26500 and it is not rechargeable.
If I...
Hi,
We have a product in production which uses the mpsl_radio_notification_cfg_set() function along with a callback to control an external GPIO when thre is radio activity...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
