Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
Hi I'm using the PCA10003 dev board to try it out the OTA firmware update.
What i did is exactly that:
Modify the bootloader example for S310 softdevice and 10003...
Hi, I have been developing with the nRF52 DK for the past couple of months however I have encountered an issue today which I am unable to resolve.
I am unable to establish...
Continuing my mission to have SES set up to be the complete development environment on a Mac I am struggling to get the Jlink Debugger to behave with SES.
It appears I...
hello , I want to Know how to write value to S0 , L ,S1.
for example : I want Set S0 =1 , L = 16 , S1 = 1 .
but I can't find any register to set S0 , L , and S1. .
My...
We are trying to reduce standby current consumption for our application. When measuring the current depending on the environment temperature we can see a rapid increase of...
My Application will have 4 difference host in the same area, if one device send a data and receive the ACK payload, is it receive all of the 4 hosts ACK payload or one of...
Hello,
I've founded the nrf_drv_lpcomp_init function didn't configure the EXTREFSEL register that why I can't configure the LPCOMP to use the AREF1 pin as an external reference...
Hi all, i have already posted in another discussion my problem, but i will resume it here briefly:
i have a simple program (similar to the tutorial of the custom service...
Hi! I want to send data from the temperature sensor from the beacon, receive them with the nrf51 and then send them to the PC via USB cable. The nrf51 has to start the connection...
Hi!
Is it possible to scan on a single channel using SoftDevice 132 running on nRF52?
If no such functionality exists, is there some workaround? Like timeslot API for...
