Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
I'm using ble_nus_string_send() to send 15 bytes over BLE UART.
As expected it sends 15 bytes, however on occasion 14 bytes are sent instead of 15 bytes.
Would there...
I ordered nrf8002 IC. I am using following breakout board PCB & not using Nordic development kit.
www.proto-advantage.com/.../product_info.php
I gave 3.3V to both VDD...
I've been working through the tutorials on BLE Services & Characteristics. That's all gone fine for me. Now I'm adjusting the sample code to use different UUIDs for my own...
Dear Sir.
I have a question for app timer in nRF52 DK(pca10040).
I was called a example source(ble_app_hts) for nRF5_SDK_11.0.0-2.alpha.
And I add UART part for logview...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
I am experiencing an error that I can't figure it out why it is happening and where to go and try to fix it.
I am using the subscriber implementation on my nRF51, Raspberry...
I see in multiple examples of NRF51 SDK:
#define APP_TIMER_MAX_TIMERS (2+BSP_APP_TIMERS_NUMBER) /**< Maximum number of timers used by the application. */
but it is...
In ble_gatts.h, I see:
#define BLE_GATTS_FIX_ATTR_LEN_MAX (510) //< Maximum length for fixed length Attribute Values.
#define BLE_GATTS_VAR_ATTR_LEN_MAX (512) //< Maximum...
Hello Everyone,
I have been working on the NRF51DK by using proxmity examples as reference when i added the static passkey for the connection security it is working well...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels? is it possible to achieve on nrf52 DK.
1>How to set up...
when i turn on the Keil, they have showed error to me
"Install missing Software Packs?
NordicSemiconductor.nRF_ConfidentialDeviceFamilyPack"
then i try to re-intall familypack...
