Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello to all,
i'm new to nRF51822 ble developing but have experience with embedded design on various microcontroller;
I have a little problem inside bootloader code: in...
Dear Nordic Support Team,
In previous SDK (6-7) I used to always call softdevice functions when possible/existing to keep compatibility with BLE.
For exemple, PPI functions...
Hi,all.i want to use nrf51822 to drive brushless DC motor and need use 6 pwm signals.Can i generate these signals with nrf51822? Thanks for your reply!
When calling sd_ble_uuid_encode() I get NRF_ERROR_INVALID_PARAM in one project while in another I get NRF_SUCCESS with the same params on same SoftDevice(S110 8.0.0) on same...
Hi,
Can a peripheral choose among multiple central?
Consider a situation where I have a 3 centrals.
Lets say CentralA, CentralB and CentralC with,
CentralA - High...
I am really puzzled by this and although I've read all the relevant answers in the Q/A I'm still unable to do the following:
do non-selective scanning with central device...
i can not re-download application by keil4
i download softdevice and the application to Equipment by nrf51422 then it can works
but when i disconnect usb line and connect...
i want to use codeblocks to compile and download program to nrf51422
so i try to compile example in keil/ARM by codeblocks
then it always show up error
like this
" C:...
Hello all, I have implemented own bond manager with saving context to flash on nRF51422 SD110.
The problem is in getting IRK and creating a whitelist with it after disconnection...
my dk board is nrf51422 and nrf 52382,
the central role is nrf51422, and the peripheral role is 52382.
my sdk version of 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I'm trying to get a module with an NFR24L01+ on board to send a simple data transmission from a pic micro but after a couple of days of trying various combinations without...
i find that the macro APP_ERROR_CHECK call the macro APP_ERROR_HANDLER
do \
{ \
const uint32_t LOCAL_ERR_CODE = (ERR_CODE); \
if (LOCAL_ERR_CODE != NRF_SUCCESS) \...
HI all:
Because the application code is relatively small, bootloader is used dual_bank_mode, but now the application code becomes large, OTA can not upgrade, I would like...
My PCA10001 board is getting detected in nRFgo studio and i can even program it but its COM port is not getting detected in device manager.
I dont know what happened but...
