Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi everybody.
I am making an application which combine ANCS and UART on PC100028 (nrf51 SDK 9.0.0). This program worked properly. However when I add DFU service (dfu_dual_bank...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
I use the S110 V7.3.0
I use the uart function ,I can use the uart function is OK.
But ,I need save power.
How can I turn off the uart function,while I was start the uart...
Hi,
When trying to update an application using nRF Toolbox on iPad, I get the error as in
this thread .
Turning Bluetooth OFF and ON does not help. On Android it works...
I tried the latest SDK 10.0 and Softdevice 8.0.3. I compiled UART_OVER_BLE examples and it works well with Android and Windows Mobile phone. However, when tested with iPhone...
Hi,Nordic and all great guys,
I am a new developer for NRF51822, and quite unfortunately ,we have a complex application to develop. We need to run code in the main thread...
Hi,
I know how to change the name of the device using
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,(uint8_t const *) DEVICE_NAME...
Hi,
I am developing a custom profile for an application.
This custom application works fine with Master Control Panel and nRF toolbox on Android.
I am also developing...
Hi,
I am using the sample ble_gls code from Nordic.
Currently it advertises for 180 sec and than resets or goes into sleep mode.
If i want to advertise continuously what...
Hello,
I am just starting working with the nRF52 development kit and have a couple guidance questions. I'm very new to the Keil environment and am having a little trouble...
I'm using s130_nrf51_2.0.0-4.alpha as central and do some testing with channel map.
I set the channel map before I'm trying to connect to a peripheral with:
ble_opt_t...
Hi experts,
I want to send 20 packages from nrf51822 to phone, so I tried to call sd_ble_gatts_hvx() repeatedly until BLE_ERROR_NO_TX_BUFFERS returns, then sent left packages...
I have a question about the NRF518222, we using 3v coin cell battery as power for Ldo working mode.
The connection between the devices and mobile phones, regular, disconnection...
nrfjprog is reporting known errors while I'm trying to burn the pca10028 dual_bank_ble_s110 bootloader to the nRF51-DK.
".\_build\nrf51422_xxac.axf" - 0 Error(s), 0 Warning...
