Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
I use the S110 V7.3.0
I use the uart function ,I can use the uart function is OK.
But ,I need save power.
How can I turn off the uart function,while I was start the uart...
Hi,
When trying to update an application using nRF Toolbox on iPad, I get the error as in
this thread .
Turning Bluetooth OFF and ON does not help. On Android it works...
I tried the latest SDK 10.0 and Softdevice 8.0.3. I compiled UART_OVER_BLE examples and it works well with Android and Windows Mobile phone. However, when tested with iPhone...
Hi,Nordic and all great guys,
I am a new developer for NRF51822, and quite unfortunately ,we have a complex application to develop. We need to run code in the main thread...
Hi,
I know how to change the name of the device using
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,(uint8_t const *) DEVICE_NAME...
Hi,
I am developing a custom profile for an application.
This custom application works fine with Master Control Panel and nRF toolbox on Android.
I am also developing...
Hi,
I am using the sample ble_gls code from Nordic.
Currently it advertises for 180 sec and than resets or goes into sleep mode.
If i want to advertise continuously what...
Hello,
I am just starting working with the nRF52 development kit and have a couple guidance questions. I'm very new to the Keil environment and am having a little trouble...
I'm using s130_nrf51_2.0.0-4.alpha as central and do some testing with channel map.
I set the channel map before I'm trying to connect to a peripheral with:
ble_opt_t...
Hi experts,
I want to send 20 packages from nrf51822 to phone, so I tried to call sd_ble_gatts_hvx() repeatedly until BLE_ERROR_NO_TX_BUFFERS returns, then sent left packages...
I have a question about the NRF518222, we using 3v coin cell battery as power for Ldo working mode.
The connection between the devices and mobile phones, regular, disconnection...
nrfjprog is reporting known errors while I'm trying to burn the pca10028 dual_bank_ble_s110 bootloader to the nRF51-DK.
".\_build\nrf51422_xxac.axf" - 0 Error(s), 0 Warning...
Hello there,
First of all, thank you Nordic for such a great platform to develop on and all the great example code to get a BLE newbie up and running. Also, a deep thanks...
