I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Teaching myself the Nordic libraries and API for nRF51 - going smoothly.
Keil uV5 and Dongle and SDK 9.0.0
Wanted to send my own data in the characteristic for HRM service...
The workaround for nRF51822 PAN#73 specifies setting an undocumented register at offset 0x0C0C of the timer peripheral to 1 prior to TASKS_START , and clearing it after TASKS_STOP...
Hi
I am trying to flash a new firmware into my device through DFU via the programming python script.
I use SDK7.2.0, and do:
ipy main.py -f c:\myproject.hex -a XXXXXXXXXXXX...
We are using the Nordic UART service for our product. Should we just use the standard UUID that the Nordic Uart uses or just generate our own for the product?
Thanks
Hi,
I'm working on an embedded system using PAN1026 bluetooth. I want to use the nRF APP to communicate with the bluetooth module. Currently I have:
Setup the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
I'm writing a build script for gcc for the nRF51 and I want to use the provided .ld scripts.
In SDK 8, those scripts were renamed from gcc_nrf51_XXX_xxab.ld to nrf51_xxab...
Hi,
I want read accel data from BNO055 sensor to NRF51 DK board, but SCL and SDA pins are 1 always.
My code is the next one:
#include "twi_master.h"
#include "twi_master_config...
I have existing design with I2C accelerometer on P0.1 and P0.2 (SDA/SCL). Don't need extreme data rates. Since examples of initializing on-board TWI don't seem to exist, and...
I am developing a tool that will be using the existing NRF51 dongle to run the S130 SD and it is being written in Python. There is no way to change any of these parameters...
Does anybody have a suggestion for a relatively low cost way to test the output power of a nRF24L01+ module? We make the modules (which are identical to the demo module) in...
Hi,
I am using the GPIOTE->PORT event to detect button presses and I would like to detect both button press and button release.
However, it seems like SENSE can only...
(this is duplicate with a support case I just opened... I hope that's okay.)
Hello, I am setting up a new laptop (our development machine caught a virus) and have installed...
Hi,
I have a sensor which sends data in a not specific time and each time start to sending data sends more that 100 data in 5 seconds
My problem is i just want one data...
