Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
Hi,
I'm writing a service to send indications on a couple of characteristics that are part of a service. In order to determine whether indications have been enabled or not...
Hi,
Is there a smaller version of the desktop 2 firmware? I don not need firmware for NFC only ble 4.0. Also would like less complicated pairing. The 6 didgit code is unnecessary...
Hi , I tried to change the transmission power using the s110 API and tried checking if the value of the register storing the transmission power is changed or not. Following...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
