Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
Hi :
I want to update the firmware of 24le1 over the air ,follow the 3 step ,fail.
download "rf_adapter_nRF24LU1P.hex " to the nRF24LU1 by nrf6310,and connect to PC...
I am using the nrf52832 to communicate uart with hw flow control and a baudrate of 9600 and fifo.
Everything is going well most of the time, but sometimes the other device...
I write an infrared receive driver on example ble_app_uart with softDevice 6, but it not work after I use softDevice 8.How to fix it ? Is there an offical infrared receive...
I'm trying to generate a 1kHz PWL and call a function every 1ms the code is below.
My initial though was to set TASKS_CLEAR once the timer reached the max pwl value.
Oddly...
Hello,
I am using multilink central example to connect to multiple peripherals. But I am facing a problem in connecting 2nd device.
After connecting the 1 st device, upon...
Hi,
the S130 supports multiple connections for the Central role. Is it possible to connect to multiple devices at the same time? E.g. calling sd_ble_gap_connect() asynchronously...
